back to top
My wish lists
Save your wish list
If you want to add more content to your wish list, simply log in. If you do not have a user account, please register for the Hanser Customer Center.

» Do you already have a user account? Please log in here.
» Don't have a user account yet? Please register here.
Your wish lists
If you want to use your wish list during your next visit, simply log in. If you do not have a user account, please register for the Hanser Customer Center.
» Do you already have a user account? Please log in here.
» Don't have a user account yet? Please register here.

« Back

Your advantages at a glance

  • One login for all Hanser portals
  • Individual home page for faster access to preferred content
  • Exclusive access to selected content
  • Personal wish lists on all portals
  • Central management of your personal information and newsletter subscriptions

Register now
Deutsch
News finder


Your search term

Technology Report

171 to 180 from 432 News

show 10  | 20 | 50
  • 11-16-2015

    Constant Mold Breathing

    With the aid of newly developed software, mold breathing during injection molding can be calculated on monitored. If the process conditions change, the clamping force is adjusted automatically to keep the mold breathing constant.   more

    Bookmark Bookmarked
  • 11-03-2015

    Homogeneous Melts at High Speeds

    Plasticating capacity during extrusion can be increased by increasing screw rpm. However, this entails the risk of unsatisfactory melt homogeneity. Investigations show that with a special mixing element the physical and thermal homogeneity of the melt can be improved.   more

    Bookmark Bookmarked
  • 10-20-2015

    A Second Life of Carbon Fibers

    A special processing technique makes it possible to use carbon fibers from production waste for compounding of carbon fiber-reinforced thermoplastics. These materials can substitute glass fiber reinforced plastics in automobile center consoles, for instance.   more

    Bookmark Bookmarked
  • 10-06-2015

    Injection Pressure Influences Flow Behavior

    The injection pressure has a significant influence on the viscosity of the polymer melt during injection molding. However, since the pressure-dependent viscosity data are usually not available, this relationship is often neglected in actual practice.   more

    Bookmark Bookmarked
  • 09-07-2015

    Thermoactive Piping System

    Retrofitting of ventilation ducts in buildings is often very complex because of unfavorable structural conditions. A thermoactive piping system that is installed as a flexible duct and then cured can simply installation.   more

    Bookmark Bookmarked
  • 09-03-2015

    Active Decoupling with Dielectric Elastomers

    Dielectric elastomers can convert electrical energy directly into mechanical work. This effect is now being used to minimize the propagation of vibrations actively.   more

    Bookmark Bookmarked
  • 08-12-2015

    Aluminum Production Molds

    Aluminum molds have a lower density and higher thermal conductivity than steel molds. Despite this, in injection molding they are used almost only for production of prototypes. Investigations have shown that under certain circumstances aluminum can also be an interesting alternative to steel for volume production.   more

    Bookmark Bookmarked
  • 07-13-2015

    Fiber Spraying Process for Efficient Preform Production

    Using a novel fiber spraying process, the orientation of fibers during fiber deposition can be adjusted as desired. By processing rovings directly, the effort associated with producing preforms is considerably less than with conventional production methods.   more

    Bookmark Bookmarked
  • 07-13-2015

    Optimized Printing Process for Organic Electronics

    Manufacturing polymer-based electronic component involves printing of conductive, semi-conductive or insulating layers on a carrier film. Even minor changes in the physical-chemical process conditions can have a significant effect on the properties of the layers.   more

    Bookmark Bookmarked
  • 06-16-2015

    Bicycle Bottom Bracket Bearing with Torque Sensor

    To determine the speed, bottom bracket bearings on electric bicycles are equipped with sensors. A support element made from PA66 can facilitate installation and at the same time increase reliability.   more

    Bookmark Bookmarked
171 to 180 from 432 News

show 10  | 20 | 50
Newsletter

Would you like to subscribe to our Newsletters on plastics technology and profit from the latest information?

Subscribe here

Subscribe here